Information came from OSHA Fact Sheet “Subpart CC – Cranes and Derricks in Construction: Wire Rope—Inspection,” which can be found at www.osha.gov.
In 2013, OSHA released a fact sheet describing the wire rope inspection requirements of the Cranes and Derricks in Construction rule. These provisions, which took effect Nov. 8, 2010, are intended to assist inspectors and supervisors, and require annual/comprehensive and monthly inspections be documented according to 1926.1412(f)(7) and 1916.1412(e)(3).
According to the rule, rope lubricants that hinder inspection must not be used, and all documents produced under this section must be available during the applicable document retention period to all persons who conduct inspections under this section.
|INSPECTION REQUIREMENTS (OSHA SUBPART CC)|
|Inspection Trigger||Inspection Details||Performed By||Documentation|
|Each Shift||See list below, visual inspection must begin prior to each shift in which the equipment is used.||Competent Person||Not Required|
|Monthly||See details below||Competent Person||Required. Must be signed by the person who conducted the inspection and retained for a minimum of three months.|
|Annually||See details below||Qualified Person||Required. Must be signed by the person who conducted the inspection and retained for a minimum of twelve months.|
In a shift inspection, a competent person must conduct a visual inspection of the wire rope prior to each shift during which the equipment is used. Shift inspections do not require untwisting wire rope or booming down, but must consist of observation of the wire ropes (running and standing) likely to be in use during the shift for apparent deficiencies.
Where a wire rope is required to be removed from service, either the equipment (as a whole), or the hoist with that wire rope, must be tagged-out until the wire rope is repaired or replaced.
CRITICAL REVIEW ITEMS
Particular attention must be given to:
- Rotation-resistant wire rope in use;
- Wire rope being used for boom hoists and luffing hoists, particularly at reverse bends;
- Wire rope at flange points, crossover points, and repetitive pickup points on drums;
- Wire rope at or near terminal ends; and
- Wire rope in contact with saddles, equalizer sheaves or other sheaves where rope travel is limited.
Each month an inspection must be conducted as stated under “Shift Inspection” above. In addition, monthly inspections require:
- The inspection include any deficiencies that the qualified person who conducts the annual inspection determines must be monitored;
- Wire ropes on equipment must not be used until an inspection under this paragraph demonstrates that no corrective action is required; and
- The inspection must be documented (monthly inspection documentation).
At least every 12 months, wire ropes in use on equipment must be inspected by a qualified person as stated under “Shift Inspection” above. In addition to the criteria for shift inspection, annual inspections require:
- The inspection be complete and thorough, covering the surface of the entire length of the wire ropes, with particular attention given to all of the following:
- Critical review items in 1926.1413(a)(3);
- Those sections that are normally hidden during shift and monthly inspections;
- Wire rope subject to reverse bends; and
- Wire rope passing over sheaves.
In the event an annual inspection under 1926.1413(c)(2) is not feasible due to existing set-up and configuration of the equipment (such as where an assist crane is needed), or conditions (such as a dense urban setting), such inspections must be conducted as soon as it becomes feasible, but no longer than an additional six months for running ropes and, for standing ropes, at the time of disassembly.
- If a deficiency is determined to constitute a safety hazard, operations involving use of the wire rope in question must be prohibited until:
- The wire rope is replaced (see 1926.1417), or
- If the deficiency is localized, the problem is corrected by severing the wire rope in two; the undamaged portion may continue to be used. Joining wire rope by splicing is prohibited. If a rope is shortened, the employer must ensure that the drum will still have two wraps of wire when the load and/or boom is in its lowest position.
- If a deficiency is identified and the qualified person determines that, though not presently a safety hazard, the deficiency needs to be monitored, the employer must ensure that the deficiency is checked in the monthly inspections.
- The inspection must be documented according to 1926.1412(f)(7);
- Rope lubricants of the type that hinder inspection must not be used; and
- All documents produced under this section must be available, during the applicable document retention period, to all persons who conduct inspections under this section.